• Concrete
• Exposed Aggregate
• Asphalt
• Slate
• Bricks
• Concrete Pools
• Fibreglass Pools
• Exterior Timber
• Metal Surfaces
• Weatherboard

• Water-based
• Fully biodegradable
• Non-flammable
• Contains no TAPs or HAPs (Toxic/Hazardous Air Pollutants)
• Non-carcinogenic
• Easy clean up with running water
• Low VOCs
• Non-ozone-depleting
• Not regulated by authorities for transportation/storage
• Not regulated by authorities for worker health and safety
• Low odour
• Will not burn skin

Additional Benefits that contribute to Cost-effectiveness:

• Requires much less chemical to achieve the desired results
• Reduces man-hours and effort required to complete a project
• Reduces the cost of waste disposal
• Reduces downtime since other work at the site can continue while the stripper does its job
• Lowers insurance costs for storage hazards.

Equipment & Tools

This product is designed for use with either spray or brush applications.

Airless sprayers are recommended. Use only airless equipment with chemical-resistant packing that can deliver a volume of 2 L/min and a pressure of 2500 psi. A typical medium-sized airless sprayer is capable of spraying this product. Equip the sprayer with a tip size of 0.019 inches or larger. (Example: a 519 or 425 tip).

Other equipment: brushes, rollers, scraper, masking tape, plastic (polyethylene) sheet, pressure washer, electric drill with mixer, empty pails for clean-up, running water, rags. Roller application should be used only for horizontal surfaces.

Preparation

Cover/protect areas where stripping is not desired, including adjoining surfaces where overspray may travel. Polyethylene sheets make a very effective barrier. If using masking tape, apply two layers of tape and remove the top layer immediately after application as the remover may soak through the tape, damaging paint under it. Plants should be covered or washed thoroughly with water before and during application.

Never shake Nu-EcoSafe-Strip Industrial. Shaking will cause the product to separate. Using a drill mixer, mix product until it is uniform in colour and is creamy in consistency, (About 1 minute 4 litre).

Remove all filters from the pump, sprayer and gun. Prime the pump and run the stripper through the hose and gun until all previous water/solvent/paint residue has been cleaned out.

Test Patch

Conduct a small test patch in an inconspicuous area to ensure product performance. This will indicate the time required for project completion, the suitability of the product for paint and substrate, and the most effective removal method.

Application Procedure

Apply a thick, even layer of stripper onto the coating being removed. An airless sprayer is the most effective means for application. Always start the sprayer pump at the lowest pressure setting and gradually increase the pressure until an adequate fan pattern is generated. High pressure and narrow tip sizes can break the stripper’s emulsion, destroying its effectiveness.

The stripper must be applied 1.5 to 2 times the thickness of the coating being removed, i.e 20 mils of coating requires 30-40 mils of stripper to be removed effectively. When trying to build up films thicker than 30 mils (600 microns), or when trying to apply the stripper on a glossy or greasy vertical surface, it is advisable to build the stripper film in two separate applications.

First, apply a light coat of approximately 15 mils (300 microns), thick enough to hide the surface colour of the coating. Allow it to dwell for 5 to 30 minutes, and then build the rest of the stripper film thickness in a second application.

Once applied, leave the stripper alone, as agitation slows down penetration. If using a brush, make sure the underlying surface is completely covered with Nu EcoSafe Strip Industrial Sacrificial Stripper.

Re-Application

When there are multiple layers of paint, poor intercoat adhesion may exist between some layers. Premature lifting may occur at this interface. If this happens, remove the lifted layers and reapply the stripper. Do not rinse with water between applications. Do not allow the stripper to dry out. The stripper is designed to remain wet and effective over extended periods (up to 48 hours). However, excessive sunshine, windy conditions, or insufficient stripper thickness can cause early drying. If the stripper starts to dry, reapply a light coating and allow extra time for completion.

Dwell Time

The time required for penetration varies depending on the type of paint, its thickness, and the surrounding temperature. Most paint systems require between 2 and 36 hours. EcoSafe Strip Industrial Sacrificial Stripper can be left overnight, but do not allow it to dry out.

Removal & Clean Up

Removal of lifted paint can be completed using a scraper, squeegee, wet/dry vacuum suction system, or a high-pressure (2,500-3,500 psi) water wash. Be cautious when using a high-pressure washer on porous surfaces, as it may damage the surface. Pressure wash from the bottom up on vertical surfaces to prevent rinse water from deactivating the stripper in sections below. The stripped surface must be rinsed with water to remove all chemical residue before repainting.

Collect lifted paint and place it in plastic containers. Add Nu EcoSafe Strip Ecozorb to absorb the remaining liquids and dispose of following local government regulations. Do not collect and/or store removed paint and stripper waste residue in metal containers. Clean up spray equipment by running water through it soon after spraying has been completed.

Download EcoSafe Strip Industrial TDS
Download EcoSafe Strip Industrial SDS

Proper safety procedures should be followed at all times while handling the product.

Refer to the Material Safety Data Sheet for important health and safety information before use.